熱處理工藝對Mg-6Zn-3Al鎂合金顯微組織和力學性能的影響

熱處理工藝對Mg-6Zn-3Al鎂合金顯微組織和力學性能的影響Effects of heat treatment technology on microstructure and mechanical properties of Mg-6Zn-3Al magnesium alloy

通過金屬型鑄造制備新型Mg-6Zn-3Al(ZA63，質量分數，%)鎂合金，并利用光鏡(OM)、掃描電鏡(SEM)、透射電鏡(TEM)、X射線衍射儀(XRD)和力學性能測試研究ZA63合金在鑄態、固溶和時效處理后顯微組織和力學性能的變化規律。結果表明：合金鑄態組織主要由基體α-Mg、晶界處呈連續或半連續分布的(α-Mg+Mg2Zn3+Mg7Zn3+Mg32(Al,Zn)49)共晶和晶內孤立的顆粒相組成。合金在350 ℃固溶12~36 h時，隨著時間延長，固溶效果逐漸增強，且在28 h時獲得了較好的組織和241 MPa的抗拉強度及11.12%的伸長率。隨后在180 ℃時效 6~72 h后，合金的抗拉強度進一步提高，力學性能隨保溫時間延長呈先增加后減小的趨勢，其中時效24 h時同時出現抗拉強度、伸長率和硬度的峰值298 MPa、9.78%和96.3 HV，比鑄態的214 MPa、8.54%、62.2 HV分別提高39.25%、14.52%和54.82%。180 ℃時效24 h后，析出相的主要形態有板條狀和短棒狀。

A new type Mg-6Zn-3Al (noted ZA63, mass fraction, %) magnesium alloy was prepared by permanent mould casting, and the microstructure and mechanical properties of the alloy under the conditions of as-cast, solution and aging treatment were systematically investigated by OM, SEM, TEM, XRD and mechanical tests, respectively. The results indicate that the as-cast alloy is mainly comprised of matrix α-Mg, eutectic phases (α-Mg+Mg2Zn3+Mg7Zn3+ Mg32(Al,Zn)49) with continuous or semi-continuous precipitated along grain boundaries and a few divorced granules within grains. When the alloy is treated at 350 ℃ for 12-36 h, the solution effects are gradually enhanced with increasing solution time. At 350 ℃ for 28 h, the alloy reveals relatively homogeneous microstructure, and the ultimate tensile strength (UTS) and elongation (EL) of 241 MPa and 11.12% are achieved, respectively. Subsequently, when the alloy is aged at 180 ℃ for 6-72 h, the mechanical test demonstrates that, the UTS further increases, the mechanical properties increase firstly and then decrease, the peak values of UTS, EL and micro-hardness of the alloy aged at 180 ℃ for 24 h are simultaneously obtained, which are 298 MPa, 9.78% and 96.3 HV and increase by 39.25%, 14.52% and 54.82% compared with those of the as-cast alloy (214 MPa, 8.54% and 62.2 HV), respectively. There are mainly two types of precipitates of the alloy after aging at 180 ℃ for 24 h, namely, the first precipitate is lath-like, the secondary one is a short-rod.

全文下載：https://pan.baidu.com/s/1TbejcZsST56x3zUYgimHMA?

作為值得信賴的合作伙伴和高品質金屬合金的半成品供應商，通項公司擁有完善的服務體系和專業的團隊。在同客戶交易的過程中，我們力求根據不同的應用需求將我們的產品做到精益求精。針對當前和未來的市場需求，通項公司致力于為客戶提供最佳的金屬材料解決方案。

TXCO has been a reliable partner and supplier of sophisticated and high-quality semi-finished products maed of alloys. In dialogue with our customers, we optimise our products to meet the specific application requirements. TXCO develops the best alloy material solutions for current and future challenges.

獲取更多我們供應的產品和服務信息，請致電086-021-6786 0205或發電子郵件service@sinoav.com聯系我們，您也可以通過微信，微博，領英，臉書，推特和谷歌+與我們互動。

For more information on the products and services that we supply, call us at 086-021-6786 0205 or email us at service@sinoav.com. You can also get in touch on social media, we are constantly active on Weixin, Weibo, LinkedIn, Facebook, Twitter and Google+.